A Novel Fabrication of Heterogeneous Saponified Poly(Vinyl Alcohol)/Pullulan Blend Film for Improved Wound Healing Application.

In this study, a novel film of poly(vinyl alcohol) (PVA)/pullulan (PULL) with improved surface characteristics was prepared from poly(vinyl acetate) (PVAc)/PULL blend films with various mass ratios after the saponification treatment in a heterogeneous medium. According to proton nuclear magnetic resonance (1H-NMR), Fourier transform infrared, and X-ray diffraction results, it was established that the successful fabrication of saponified PVA/PULL (100/0, 90/10, and 80/20) films could be obtained from PVAc/PULL (100/0, 90/10, and 80/20) films, respectively, after 72 h saponification at 50 °C. The degree of saponification calculated from 1H-NMR analysis results showed that fully saponified PVA was obtained from all studied films. Improved hydrophilic characteristics of the saponified films were revealed by a water contact angle test. Moreover, the saponified films showed improved mechanical behavior, and the micrographs of saponified films showed higher surface roughness than the unsaponified films. This kind of saponified film can be widely used for biomedical applications. Moreover, the reported saponified film dressing extended the lifespan of dressing as determined by its self-healing capacity and considerably advanced in vivo wound-healing development, which was attributed to its multifunctional characteristics, meaning that saponified film dressings are promising candidates for full-thickness skin wound healing.

Study of Damage Prediction of Carbon Fiber Tows Using Eddy Current Measurement.

When manufacturing fiber-reinforced composites, it is possible to improve the quality of fiber steel fire and reduce the number of cracks in the finished product if it is possible to quickly identify the defects of the fiber tow. Therefore, in this study, we developed a method to identify the condition of carbon fiber tow using eddy current test (ECT), which is used to improve the quality of composite materials. Using the eddy current detection sensor, we checked the impedance results according to the condition of the CF tow. We found that the materials of the workbench used in the experiment greatly affected the ECT results, so it is necessary to use a material with a non-conductive and smooth surface. We evaluated the impedance results of the carbon fiber at 2 mm intervals using the ECT sensor and summarized the impedance results according to the fiber width direction, presenting the condition of the section as a constant of variation (CV). If the condition of the carbon fiber tow was unstable, the deviation of the CV per section was large. In particular, the deviation of the CV per section was more than 0.15 when the arrangement of the fibers was changed, foreign substances were formed on the surface of the fibers, and damage occurred in the direction of the fiber width of more than 4 mm, so it was easy to evaluate the quality on CF tow.

Blown Composite Films of Low-Density/Linear-Low-Density Polyethylene and Silica Aerogel for Transparent Heat Retention Films and Influence of Silica Aerogel on Biaxial Properties.

Blown films based on low-density polyethylene (LDPE)/linear low-density polyethylene (LLDPE) and silica aerogel (SA; 0, 0.5, 1, and 1.5 wt.%) were obtained at the pilot scale. Good particle dispersion and distribution were achieved without thermo oxidative degradation. The effects of different SA contents (0.5-1.5 wt.%) were studied to prepare transparent-heat-retention LDPE/LLDPE films with improved material properties, while maintaining the optical performance. The optical characteristics of the composite films were analyzed using methods such as ultraviolet-visible spectroscopy and electron microscopy. Their mechanical characteristics were examined along the machine and transverse directions (MD and TD, respectively). The MD film performance was better, and the 0.5% composition exhibited the highest stress at break. The crystallization kinetics of the LDPE/LLDPE blends and their composites containing different SA loadings were investigated using differential scanning calorimetry, which revealed that the crystallinity of LDPE/LLDPE was increased by 0.5 wt.% of well-dispersed SA acting as a nucleating agent and decreased by agglomerated SA (1-1.5 wt.%). The LDPE/LLDPE/SA (0.5-1.5 wt.%) films exhibited improved infrared retention without compromising the visible light transmission, proving the potential of this method for producing next-generation heat retention films. Moreover, these films were biaxially drawn at 13.72 MPa, and the introduction of SA resulted in lower draw ratios in both the MD and TD. Most of the results were explained in terms of changes in the biaxial crystallization caused by the process or the influence of particles on the process after a systematic experimental investigation. The issues were strongly related to the development of blown nanocomposites films as materials for the packaging industry.

An Investigation on the Feasibility of Fabricating Composites Using Outdated Waste Carbon Fibers and Easily Disposable Polyolefin Resins.

Outdated-waste-carbon-fiber-reinforced olefin composites (oCFOCs) were fabricated with easily disposable polyolefin resins, polypropylene (PP), high-density polyethylene (HDPE), and low-density polyethylene (LDPE), by compressive molding using a hot press. The flexural and impact strengths of the oCFOCs from each respective resin type and oCF content, ranging from 35 to 70 wt.%, were increased by the aging treatment (120 °C and 95% humidity under a pressure of 0.8 MPa) until an aging time of three days, due to improved resin impregnation. For the oCFOC with PP, the hydrogen bond between PP and developed C-O groups due to the aging treatment and the existing silane layer of oCF is considered to assist cohesion between the resin and oCF. In particular, PP and 45 wt.% oCF content were the most effective conditions for improving the oCFOCs' mechanical properties, in addition to endowing the oCFOCs with good moldability and dimensional stability. Our results demonstrate that durable recycled composites can be manufactured using oCF and PP.

Surface control and cryogenic durability of transparent CNT coatings on dip-coated glass substrates.

Transparent carbon nanotube (CNT) coatings were deposited on boro-silicate glass substrates by dip-coating. Ultraviolet-visible (UV) spectra, surface resistance measurement, and the wettability tests were used to investigate the optical transmittance and electrical properties of these CNT coatings. The changes in electrical and optical properties of these coatings were observed to be functions of the number of dip-coating cycles. The surface resistance of the CNT coated substrates decreased dramatically as the number of dip-coatings was increased, whereas the increases in the CNT layer thickness beyond that for the first dipping cycle had little effect on the transparent-properties. Static contact angle measurements proved to be an effective means for evaluating the surface morphology of CNT coatings. The interfacial durability of the CNT coatings on a glass substrate was much better than that of ITO coatings over the temperature range from -150°C to +150°C.